pg_upgrade

Optionally move the old cluster

If you are using a version-specific installation directory, e.g. /opt/PostgreSQL/9.1 , you do not need to move the old cluster. The graphical installers all use version-specific installation directories.

If your installation directory is not version-specific, e.g. /usr/local/pgsql , it is necessary to move the current PostgreSQL install directory so it does not interfere with the new PostgreSQL installation. Once the current PostgreSQL server is shut down, it is safe to rename the PostgreSQL installation directory; assuming the old directory is /usr/local/pgsql , you can do:

mv /usr/local/pgsql /usr/local/pgsql.old

to rename the directory.

For source installs, build the new version

Build the new PostgreSQL source with configure flags that are compatible with the old cluster. pg_upgrade will check pg_controldata to make sure all settings are compatible before starting the upgrade.

Install the new PostgreSQL binaries

Install the new server's binaries and support files.

For source installs, if you wish to install the new server in a custom location, use the prefix variable:

make prefix=/usr/local/pgsql.new install

Install pg_upgrade and pg_upgrade_support

Install the pg_upgrade binary and pg_upgrade_support library in the new PostgreSQL installation.

Initialize the new PostgreSQL cluster

Initialize the new cluster using initdb . Again, use compatible initdb flags that match the old cluster. Many prebuilt installers do this step automatically. There is no need to start the new cluster.

Install custom shared object files

Install any custom shared object files (or DLLs) used by the old cluster into the new cluster, e.g. pgcrypto.so , whether they are from contrib or some other source. Do not install the schema definitions, e.g. CREATE EXTENSION pgcrypto , because these will be upgraded from the old cluster. Also, any custom full text search files (dictionary, synonym, thesaurus, stop words) must also be copied to the new cluster.

Adjust authentication

pg_upgrade will connect to the old and new servers several times, so you might want to set authentication to peer in pg_hba.conf or use a ~/.pgpass file (see Section 31.15 ).

Stop both servers

Make sure both database servers are stopped using, on Unix, e.g.:

pg_ctl -D /opt/PostgreSQL/8.4 stop
pg_ctl -D /opt/PostgreSQL/9.0 stop

or on Windows, using the proper service names:

NET STOP postgresql-8.4
NET STOP postgresql-9.0

or

NET STOP pgsql-8.3  (PostgreSQL 8.3 and older used a different service name)

Run pg_upgrade

Always run the pg_upgrade binary of the new server, not the old one. pg_upgrade requires the specification of the old and new cluster's data and executable ( bin ) directories. You can also specify user and port values, and whether you want the data linked instead of copied (the default).

If you use link mode, the upgrade will be much faster (no file copying) and use less disk space, but you will not be able to access your old cluster once you start the new cluster after the upgrade. Link mode also requires that the old and new cluster data directories be in the same file system. (Tablespaces and pg_xlog can be on different file systems.) See pg_upgrade --help for a full list of options.

The --jobs option allows multiple CPU cores to be used for copying/linking of files and to dump and reload database schemas in parallel; a good place to start is the maximum of the number of CPU cores and tablespaces. This option can dramatically reduce the time to upgrade a multi-database server running on a multiprocessor machine.

For Windows users, you must be logged into an administrative account, and then start a shell as the postgres user and set the proper path:

RUNAS /USER:postgres "CMD.EXE"
SET PATH=%PATH%;C:\Program Files\PostgreSQL\9.0\bin;

and then run pg_upgrade with quoted directories, e.g.:

pg_upgrade.exe
        --old-datadir "C:/Program Files/PostgreSQL/8.4/data"
        --new-datadir "C:/Program Files/PostgreSQL/9.0/data"
        --old-bindir "C:/Program Files/PostgreSQL/8.4/bin"
        --new-bindir "C:/Program Files/PostgreSQL/9.0/bin"

Once started, pg_upgrade will verify the two clusters are compatible and then do the upgrade. You can use pg_upgrade --check to perform only the checks, even if the old server is still running. pg_upgrade --check will also outline any manual adjustments you will need to make after the upgrade. If you are going to be using link mode, you should use the --link option with --check to enable link-mode-specific checks. pg_upgrade requires write permission in the current directory.

Obviously, no one should be accessing the clusters during the upgrade. pg_upgrade defaults to running servers on port 50432 to avoid unintended client connections. You can use the same port number for both clusters when doing an upgrade because the old and new clusters will not be running at the same time. However, when checking an old running server, the old and new port numbers must be different.

If an error occurs while restoring the database schema, pg_upgrade will exit and you will have to revert to the old cluster as outlined in step 14 below. To try pg_upgrade again, you will need to modify the old cluster so the pg_upgrade schema restore succeeds. If the problem is a contrib module, you might need to uninstall the contrib module from the old cluster and install it in the new cluster after the upgrade, assuming the module is not being used to store user data.

Restore pg_hba.conf

If you modified pg_hba.conf , restore its original settings. It might also be necessary to adjust other configuration files in the new cluster to match the old cluster, e.g. postgresql.conf .

Post-Upgrade processing

If any post-upgrade processing is required, pg_upgrade will issue warnings as it completes. It will also generate script files that must be run by the administrator. The script files will connect to each database that needs post-upgrade processing. Each script should be run using:

psql --username postgres --file script.sql postgres

The scripts can be run in any order and can be deleted once they have been run.

Statistics

Because optimizer statistics are not transferred by pg_upgrade , you will be instructed to run a command to regenerate that information at the end of the upgrade. You might need to set connection parameters to match your new cluster.

Delete old cluster

Once you are satisfied with the upgrade, you can delete the old cluster's data directories by running the script mentioned when pg_upgrade completes. (Automatic deletion is not possible if you have user-defined tablespaces inside the old data directory.) You can also delete the old installation directories (e.g. bin , share ).

Reverting to old cluster

If, after running pg_upgrade , you wish to revert to the old cluster, there are several options:

• If the --check option was used, the old cluster was unmodified; it can be restarted.

• If the --link option was not used, the old cluster was unmodified; it can be restarted.

• If the --link option was used, the data files might be shared between the old and new cluster:

  • If pg_upgrade aborted before linking started, the old cluster was unmodified; it can be restarted.

  • If you did not start the new cluster, the old cluster was unmodified except that, when linking started, a .old suffix was appended to $PGDATA/global/pg_control . To reuse the old cluster, remove the .old suffix from $PGDATA/global/pg_control ; you can then restart the old cluster.

  • If you did start the new cluster, it has written to shared files and it is unsafe to use the old cluster. The old cluster will need to be restored from backup in this case.